alat peraga SMK - STM Otomotif

1 Car Training Stand Engine : four cylinder, four strokes, Transmission : manual, 4 speed, Suspension : axle type, The trainer completes with all vehicle components including chassis of vehicle, The trainer without body, Electrical system : completed with standart electrical system (without wiper), Completed with ignition system, Completed with charging  2 Diesel Engine Trainer Stand Engine : four-cylinder, four stroke diesel engine, water-cooled, in line type 2000 - 2500 cc (variation mark) Instrument panel : key type ignition switch, ampere meter, oil control lamp, water temperature gauge. Sub-system : Radiator cooling system, fuel system with 5 liter fuel tank, exhaust system. On model is fully operable. The engine has four inch polyurethane wheels for  mobility and two of the wheels have locks in order to keep the engine stationary during operation The rebuilt engines have been restored to "like new" condition, and are guaranteed to give  excellent performance. The reconditioned engines offer good value 3 Gasoline Engine Trainer Stand  Engine : four-cylinder, four stroke gasoline engine, water-cooled, 1000 - 1500 cc (variation mark) Instrument panel : key type ignition switch, ampere meter, oil control lamp, water temperature gauge. Sub-system : Radiator cooling system, fuel system with 5 liter fuel tank, exhaust system. On model is fully operable. The engine has four inch polyurethane wheels for  mobility and two of the wheels have locks in order to keep the engine stationary during operation The rebuilt engines have been restored to "like new" condition, and are guaranteed to give  excellent performance. The reconditioned engines offer good value 4 Gasoline Engine Trainer Stand (EFI) Engine : In line type engine, four-cylinder, four stroke gasoline, Instrument : key type ignition switch, ampere meter, oil control lamp, water temperature gauge. Sub-system : Radiator cooling system, fuel system with 5 liter fuel tank, exhaust system, and 40 AH battery with cables Stand from profile iron mounted on a 4 inch, poly-urethane wheel for easy mobillty 5 Engine Training Stand Model (gasoline) Engine : In line type engine, four-cylinder, four stroke gasoline engine. Stand from profile iron mounted on a 4 inch poly-urethane wheel for easy mobility. 6 Engine Training Stand Model (diesel) Engine : four-cylinder, four stroke diesel engine, in line type 2000 - 2500 cc (variation mark). On model is fully operable. The engine has four inch polyurethane wheels for mobility and two of the wheels have locks in order to keep the engine stationary during operation The rebuilt engines have been restored to "like new" condition, and are guaranteed to give excellent performance. The reconditioned engines offer good value to 7 Four Stroke Engine Model Engine : 4 strokes, Ignition : Conventional magnet The engine is mounted on a wooden base 8 Motor Cycle Life Trainer Stand Engine : 2 strokes motorcycle engine, 80 - 110 cc Instrument : key type ignition switch Sub-system : air cooling system, fuel system with 1 liter fuel tank Electricity System : Head Light, Rear Light, Town Light & Sign Lamp. Ignition : CDI system 9 Two Stroke Engine Model Engine : 2 strokes Ignition : Conventional magnet The engine is mounted on a wooden base 10 Inline  Diesel Injection Pump Model  Original Rotary Diesel injection pump 4 elements with delivery pump Centrifugal governor system 11 Rotary Diesel Injection Pump Model Original Rotary Diesel injection pump 4 elements with delivery pump Centrifugal governor system 12  Injection pump Model Rotary Type Original in-line injection pump 4 elements with delivery pump Centrifugal governor system 13 Power Train Training System Reconditioned unit offer excellent value to school, as student are able to detect point of wear which is useful in any training program. Original component of transmission, Propeller shaft, differential, wheel axle.Stand from tubular iron. 14 Independent Suspension Strut Type l Complete front-end of a vehicle that is ideal for demonstrating the operation and interaction of the steering and suspension mechanism. Through of this trainer student may be exposed to the function of the stabilizer, shock absorber and steering linkage suspension system. Units are  reconditioned so as all part are fully operable and have been cleaned and painted Easy mobility (on 4 wheels) 15 Differential Gear Model The real axle is use recondition The unit is to be mounted on a sturdy steel floor stand that is provided with wheels for mobility Steel is to be painted 16 Power Steering Trainer Rack and pinion powered by AC electric motor 2 HP 17 Standard Body Electrical Trainer Stand (car) The elctrical standard body is designed to realistically simulate the electrical system on an automobile. The unit consists of a number of modular demonstration panel which are mounted on a wheeled stand that contains a power source and component connecting cable. The original parts as commonly used in automobiles typically produced by the major car or component manufacturer. The components are mounted on clear plexy glass panels that allow high visibility af all parts and wiring. Vertical presentation of panels simulates the schematic presentation of common vehicle wiring diagrams. Panel feature wiring guides and icon which have been silk screened on to the panels so as to familiarize the student with schematic type wiring diagrams  Body electrical standard components. : Head light, interior light, license plate light, fog light, switch, relay, wiper  and cable 18 Starter Motor Trainer Stand Original starter motor Idle load current 100 A Full load current 300 A Carefully section and painted Free wheel pinion gear Stator and rotor, brush 19 Conventional Ignition System Training Stand Conventional ignition components : - distributor, ignition coil, spark plug and cable, Battery, ignition switch, electric motor, Stand from profile iron 20 Computer Ignition System Material : Plexiglas, L Profile Alumunium, Component : Ignition key, Coil & computer, RPM Censor, Ampere meter, Volt meter, Spark plug cable, Connector Cable, Electric motor, Fuse box 21 Charging System Model Trainer  This trainer have all component of charging and completely carefully sectioned for easy identification. Alternator: To act as generator to supply all electrical system in the car and to recharge, the battery when the car engine is on, Mechanical Regulator: To regulate, mechanical, the voltage (coming from the alternator) according to the current used by an the car Electrical Regulator: To regulate electrical, (coming from the alternator) according to the current by an car Filling Control Light: To facilitate control of whether the filling system is running or not Battery: An electronic chemical electricity, storage device. Switch: To connect circuit of charging. 22 Electronic Ignition System (TCI - Hall) Material : Plexiglas, L Profile Alumunium, Component : Ignition key, Coil, Distributor, Control Unit, Ampere meter, Volt meter, Spark plug, Spark plug cable, Connector cable, Electric motor, Fuse box 23 Electronic Ignition System (TCI - Inductive) Material : Plexiglas, L Profile Alumunium, Component : Ignition key, Coil, Distributor, Control Unit, Ampere meter, Volt meter, Spark plug, Spark plug cable, Connector cable, Electric motor, Fuse box 24 Vehicle Air Conditioner Trainer Stand Motor 220 V AC/ 4 HP, evaporator with blower, condenser with fan, filter, dryer, thermostat, shigt glass, fault valve, ampere meter, volt meter 25 Central Lock, Alarm and Power Window Trainer This trainer have all components of alarm, central lock and power windows :  Central lock : Key type  ignition switch, fuse box, central lock electric switch Alarm : 4 pcs control lamp, vibration sensor, control alarm unit, switch Power window : Power window motor right & left, relay power window switch right and left. 26 Automatic Transmission System Model Original automatic transmission that was being sectioned carefully and color coded, so that the key components can be identified clearly. 27 Rear Axle Education System Reconditioned unit offer excellent value to school, as student are able to detect point of wear which is useful in any training program. Original component of transmission, Propeller shaft, differential, wheel axle. Stand from tubular iron. 28 Ball and Nut Steering Education System 29  Trainer Starting System Original starter motor Idle load current 100 A Full load current 300 A Carefully section and painted Free wheel pinion gear Stator and rotor, brush 30 Clutch System Original friction clutch was being sectioned carefully and coloured coded, so that componen can be identified clearly 31 Rear Axle Assembly System Original rear axle system offer excelent value to student are able to detect point of rear axle system 32 Turbocharger Material : Wood, component Component : Turbocharger unit Mounted on finished high quality wood 33 Front Wheel Drive Manual Transmission Original front wheel drive transmission that was being sectioned carefully and color coded, so that the key components can be identified clearly. 34 Electronic Ignition with stopper switch System Material : Plexiglas, L Profile Alumunium, Component : Ignition key, Coil, Distributor, Control Unit, Ampere meter, Volt meter, Spark plug, Spark plug cable, Connector cable, Electric motor, Fuse box 35 Distributorless Ignition System Unit engine management system Stand from profile alumunium & acrylic 36 Standard Body Electrical Trainer Stand (motor cycle) The unit consists of original bicycle electrical components which are mounted onto a simulated model.The components ate attached to the simulated board in approximately the same position as found on a bicycle standard electrical are : - Head lamp of bicycle - Turn signal front and rear - Stop and position lamp - Holder switch right and left - Flasher - Horn - Ignition switch Stand from profile iron and wood easy mobility (on 2  nch polyurethane wheels) 37 Diesel Engine Trainer Stand ( Turbo ) Engine : four-cylinder, four stroke diesel engine with turbo system, water-cooled, in line type 2000 - 2500 cc (variation mark) Instrument panel : key type ignition switch, ampere meter, oil control lamp, water temperature gauge. Sub-system : Radiator cooling system, fuel system with 5 liter fuel tank, exhaust system. On model is fully operable. The engine has four inch polyurethane wheels for  mobility and two of the wheels have locks in order to keep the engine stationary during operation The rebuilt engines have been restored to "like new" condition, and are guaranteed to give  excellent performance. The reconditioned engines offer good value 38 Power Steering Electronic 39 Motor Cycle Life Trainer Stand Engine : 4 strokes motorcycle engine, 80 - 110 cc Instrument : key type ignition switch Sub-system : air cooling system, fuel system with 1 liter fuel tank Electricity System : Head Light, Rear Light, Town Light & Sign Lamp. Ignition : CDI system B. EQUIPMENT 1 Vehicle Wheel Alignment (Laser Series) Spooring accuracy 1 mm, measuring wheel clamp R 10” - 16”, Measuring range - 10 mm - + 15 mm, Standard accessories, Wheel clamp 2 pcs, Turn table 2 pcs, Calibration 1 pce, key heigh steer 1 pce, Automatic charger 2 Vehicle Wheel Alignment (GOBA) Dimension 230 x 90 mm, camber -5o - +5o, caster -3 - 0 - 10o, kingpin 0 - 16o, weight 1,7 kg 3 Turning table gauge Capacity 2 ton, angle measurement 35 degree 4 Scantool  Asian Kit System 128MB SD-RAM, Storage HDD 20GB, Display 7" ,  Scope 4 Chanel, Multimeter, Analysis Waveform, Comunication USB 1.1, USB 2.0, Client LAN, RS-232, Keypad 4-Direction key, 6 Function Key (bottom), Battery Smart Li-ion Battery, 1 hour life, Power Supply DC-in cigar Jack (12V) 5 Engine tune-up analyzer  Okuda EA - 800 Dwell , RPM , Timing , Vacum 6 Digital Injector Tester Cleaner Ambient Temp -10 - 40 deg C Relative humidity less than 85% Environment Magnet Intensity < 400 A/m Power AC 220V Range Pressure adjustment 0 - 0.65 Mpa Length Pressure adjustment 0.004 Mpa Simulating Test 10-9990 rpm Counting Range 1-9999 times Timing Range 1-9999 seconds Range of Pulse Width 1.5-25 ms Include compressor 0.25 HP Volume 2500ml 7 Wheel Alignment 8 Sensor Temperature 0-40 deg C , CCD Infrared cable communication Relative humidity